I've got a Roland Juno DS-88 that sounds great for some things, like pipe organs and grand pianos. I have it set to midi channel 8, but it responds to every channel input.
After much back-and-forth with Roland, they came up with a way to filter everything else but channel 8 out, but it's an extremely large amount of work on an interface I don't enjoy using.
Is there a way for the MRCC to only send midi signals on channel 8 to this  keyboard? To block out everything but channel 8? I'm trying to read the manual for the MRCC but I don't really see a way to do this.
Anyone got any ideas?

Hello
Question about types of keyboards that can be used for editing labels …
Can I use a Bluetooth keyboard eg the usb Bluetooth dongle? 

Thanks.

I just ordered an MRCC and my plan is to use it with an iPad Pro as my central "control plane" for everything audio and MIDI. I will have all my synths' MIDI going through the MRCC and all my synths' audio going through a Scarlett interface. Both of the Scarlett and MRCC will be plugged in to a USB hub and I will be using AUM to manage everything on the iPad.

After ordering everything, I got a horrible feeling when I realized I wasn't sure if the MRCC will work correctly when not plugged directly into my iPad but through a USB hub (using an Anker hub if it matters). Will I run into any issues? I ask because I've had issues in the past controlling USB of MIDI devices if they were going through a USB hub.

To be clear, I am not trying to use the MRCC *as* a hub, I want to connect it to my iPad *through* a USB hub. I wanted to call this out as I saw some other people asking about using the MRCC as a hub.

Thanks in advance!

Hi. I recently did a factory reset, since when Motif 1 has been running at twice the speed of Motif 2 when they are on the same clock division. I'm using the latest firmware, but have also tried re-installing it, but the problem persists. Any advice?

Hi ?? all!

I’m excited to be using my new MRCC with my Elektron gear … but second day in … the monitor isn’t showing any data occurring or shown … 

Wasn’t like this when I first got it in day one.
There was data happening 

But now the LOAD/SAVE is on Factory … where as when I first turn on and connected it showed red user I think ? 

Any ideas ? thanks.

This may be stupidity on my part but here goes:

I Have the MRCC connected to my Mac via the PC connection.
I have no problem creating music in Logic and having it control external MIDI devices. It works great.

However, When I try to play soft synths on my Linnstrument (connected to USB B on MRCC) I get nothing.
In fact the blue light under the PC connection will not stay lit. It turns blue only while holding down. How do 
I get it to RECEIVE controller info?

Thanks!

Hey, 

So I have the MRCC and while it works like a charm... I find once all the wires are connected, using the actual controls becomes a pain.

Is there any official software or non official software I can use to create or control presets?

I know it defeats the purpose, but this scenario will only get worse once I rack the unit

Testing various configurations this morning and it seems that when connecting to a Mac, the MRCC is not recognized when I use a USB B to C cable,  but is fine when I use a USB B to A.

I tried powering down the MRCC  and also hot swapping the cables with no success. I did not try rebooting the Mac each time because ... 

Interestingly, the new MRCC 880 works just fine connected to either A or C ports.  Hot swapped or power cycle the 880, either creates a valid connection.

Hi, brand new MRCC user and curious if there are any pros/cons connecting via USB vs Midi din (besides one USB cable vs 2 for midi in and out). Guess if I could also power the unit via the USB connection it would be a plus.

I have a few controllers and synths that have both so looking for guidance before I start rewiring everything.

Thanks

I had the FW button held down for around 5-10 seconds and now my NDLR won't turn back on/show any sign of life.

Has anyone had this issue before and know a fix for it?

(10-04-2022, 10:17 PM)yozoto Wrote: I had the FW button held down for around 5-10 seconds and now my NDLR won't turn back on/show any sign of life.

Has anyone had this issue before and know a fix for it?