Apologies if this has been discussed already, and it is likely obvious to most, but worth mentioning...

If you have a midi controller driving the NDLR take care not to touch any of the controller's sliders, knobs etc while on the NDLR's channel. 

There are a few cool abilities like being able to change scale or tempo using a knob or being able to change your knob midi assignments on the fly, but in most cases it causes some menus to produce strange results, eg the Keyboard Control setting in Settings Menu 1 gets really screwy, showing options you cannot otherwise select. 

It can be fun, but in most cases getting too knobby creates unpredictable results. I wouldn't mind seeing this more flushed out though! I would love to assign all of the NDLR's different encoder options to an external controller.

Develop rack ears for 19” rack...

(My NDLR is connected MIDI IN B to Deluge MIDI OUT, NDLR MIDI OUT A to Deluge MIDI IN
 MOTIF 1 "CLK OUT on boot screen is switched OFF
 NDLR has external SYNC by Deluge)

When I turn the Position (knob top right) from MOTIF1 down to lower values the mystery starts: The Deluge speeds up in tempo throughout till max or - in other cases it slows down which can be "controlled" by not turning the Position knob too far to the left.
In other situations deluge startet recording what was also caused by the NDLR
There seems to be a correlation with higher Patt Length (also top right) but I am not sure yet.
I have got to make some MIDI OX logs sometime, but at the time I´ve got no MIDI interface for PC.

By the way: Factory reset did not help.

I really like the NDLR but this issue prevents excessive ndling at the moment.

I will keep on exploring

As the title says, would be really nice to have the strum pattern as a LFO modulation.

I am using my NDLR as my master clock because it has the most stable clock of my entire setup. 

I want to be able to start the clock (press "play") but NOT start the pads, drone, or motifs. I want those to ALWAYS be manually engaged. 

Is there a setting to change the play button to work this way? Or something else?

Thanks

I might just be misunderstanding this feature.

I assumed the midi start/stop output setting sent only midi start/stop signals. 

I assume that if I set midi start/stop output to "all" that it should not interact with the midi assignments for drone, pad, and motifs. 

But when I set the midi start/stop output to "all" it wildly interferes with what is being sent to the other midi outs. It seems like the start/stop output is sending notes also! 

My NDLR is ths most ROCK SOLID midi clock of my entire setup and my Blofeld depends on this, otherwise it "clicks" eg as Ableton tempo drifts. But I need NDLR to output start/stop to usb AND midi without interacting otherwise. Is that possible?

Thanks!

Is it possible to send a Program Change message to one of the DIN MIDI ports?

I understand that I can set up 2 CC messages assigned to 2 encoders, and this works. I did not find anything about Program Changes though. Wondering if it is technically possible.

I use this powerful little arpeggio magic box every day!  But just today I noticed that chord buttons II and VI no longer change the chord.

They do work when I shift-click them, so this feels like a software issue.

I'll be honest and say everything felt peachy until the recent update. Since then I have had notes sticking, heard clicking in some of the loops, and now this button issue. Before the recent firmware update I NEVER had a stuck note and never needed to use the panic button. Now I use it regularly. 

Please help!

Thanks!

Getting some cool patterns from the ndlr.

https://soundcloud.com/jesse-smits/snippers

Hi i'm enjoying the NDLR a lot.

Here are some findings.

1. I'm getting a click sound for 30% when a midinote arrives in my Microvolt 3900.
If i set my ADSR in the Microvolt 3900 with a slow attack i still hear a click coming in. This only happens with the NDLR at the moment. Other devices don't create this click such as the arturia keystep.

You can hear it in the beginning of this track. You hear that the microvolt is not really clean. 

https://soundcloud.com/jesse-smits/snippers

2. Other thing is. The sequencer plays low notes on some numbers. So if i make steps 1 2 3 4 5 6 7 8 9 10 11 12 13 14. Then the 9 and 11 create a lower note than numbers 1 2 4 5 6. Its like it jumps an octave.

3. It would be nice if the LFO's that im sending that go to midi inputs of other devices start doing their LFO-ing when i start playing all or a motive, pad or drone. 


Maybe one of these things were allready found.
Maybe one of these things allready have a solution.

Thanks.

Keep it up with the good project!