Maybe I shouldn't take care of that, but I have just idea to reduce of "flying" midi commands to output devices. Some of gears use only one, or two input channels. As there is input/output filtering for CC/Note/Clock etc comments, it could be useful (for "cleaning" / optimize reason) to select active midi channel(s) and all different that defined will be ignored. 

Now if i allow routing from my sequencer (for example 4 channels CH1-CH4) to all synths, this will send every midi commands to each of them, for all channels. If I define that my synth on OUT1 use only CH1 then all commands sent to CH2, CH3, CH4 will be ignored on OUT1.

Hello,

I have request to add possibility to send CC from one channel to all channels. No, I don't want to flood by CC messages, but it will allow to use one USB controller to all synths - not the same time, but only if I select routing between them. For example:

- I have midi USB controller - it allow me to modify single of few CC. It send commands on one, specified channel. I can't change it without computer. For this example it's CH16. It send CC command, for example Cutoff.
- I have (for example) 5 synths, on connected to different midi ports/outs. All synths works on different midi channel (for example OUT1 - CH1, OUT2 - CH2, OUT3 - CH3, OUT4 - CH4, OUT5 - CH5).

If i create routing between USB controller and all 1-5 OUTS then none of them will respond for CC command, because CC message is on CH16.
I can't create one rule that will send everything from CH16 to CH1, CH2, CH3, CH4, CH5, because this modifier allow only for one the same input channel. I don't want to "lose" all Channel modifiers for that, because it's very limited.

So if I could copy everything from CH16 to all channels, then i could turn on/off routing between USB-OUT1-5 on the fly and can use one controller for different synths, or even control few of them the same time. 

We could also reduce of midi messages in other way, i just got and another idea and I'll post in in new thread.

We've just ordered samples of this accessory for testing and want to gauge interest to help us decide how many to make. Its a 4 DIN input and 1 DIN output expander for MRCC. It uses an MRCC USB host port, and each DIN port is automatically connected to the USB host port's 4 ins and 1 out USB virtual MIDI ports. An MRCC can host 4 of these, if you don't mind giving up the USB host ports.

   

You could use a short USB cable to have it close to MRCC, or a longer cable to get it to where you need more I/O. USB 2.0 has a cable limit of about 5 meters, or you could use an active USB extension cable and go further. 

Besides acting as a DIN (and 3.5mm type A jack) expander for MRCC, it can be used with your PC as a 4 in to 1 out MIDI interface. Or, use it as a USB powered 4 to 1 MIDI merger.

The street price will be in the ballpark of $80 USD, but we haven't bottomed out on the full cost yet so it could go up or down a bit.

We've had a fairly high attached rate for the Remote 7 to add outputs. Would this be just as interesting? Do you need it? Please comment below  

Hello,
I would like to order the MRCC to Germany.
Can someone tell me please what is the "best"
safest and most compatible with customs shipping?

Which of the 4 offers should I use? (HK? UPS?)


Best regards
Klaus

NDLR Jam by Analogue Mastering (soundcloud.com)

I was about to purchase an MRCC when I realized how expensive the shipping was. It seems these units are shipped from outside the US? 
I am located in the US and was wondering if anyone carries these units locally, so I don't have to pay international shipping.

Thanks!

I am seeing some odd behavior with my MRCC and its USB ports.

I have an M8 (Handheld tracker) which has both midi din in/out (1/8th") and midi over USB. I have a very simple sequence on a single midi channel playing on the M8. It is sending clock, transport, and program change .

1. When sending this channel out to a synth (Intellijel Palette Midi 1u) via midi din (out port 7) the sequence plays perfectly. However, when I try to route the same data to the USB port on the Palette (USB in/out A on the MRCC) I get randomly skipped notes/ CC data. Clock & start/stop are still sent fine.

2. The other problem I am seeing with my USB ports is that the M8 USB out (fully class compliant) is ignored (no data at all registers on the MRCC).

3. And finally I am getting Hard locks about 25% of the time on the MRCC if I cycle power on the Intellijel Palette while the USB is plugged into the MRCC.

I have been slowly debugging this the last few days, so if you need additionaly info/ video I can certainly add that

If I read the manual right the PC in out has 12 configurable in/outs but my PC shows MRCC 1-16

What gives?

I have a fairly complex setup where the MRCC is connected to a Cirklon2 via the Cirklon’s device port USB2 and USB3 Virtual cables routed to physical port 2 to the TX816 and physical port3 to the DeepMind. Master keyboard is any that are input to the Cirklon2, or a Chordmonger input direct via USB B to the MRCC and routed to the Cirklon on physical USB A. I’m getting stuck notes on my TX-816 and my DeepMind. Midi Clock is being sent from the Cirklon to virtual USB3 (to the DeepMind) and to the MRCC Remote’s port 3 via virtual cable 4. 

Any idea how to stop the stuck notes? Is it a bug in the MRCC that it seems to drop note-offs? 

Joel

My NDLR only transmits note info on MIDI output 2 but not MIDI out 1
MIDI output 1 only transmits start/stop commands but MIDI out 1 does not.
This is definitely a flaw or defect.