Hey all!

The last 24 hours have been "interesting", and this forum has been super helpful in not letting it go much past that! I needed sleep!


I've had my MRCC for a while, never thought about updating it, then I did think about updating it. That was about 24 hours ago.  

When I started down the update road, at some point I hit the FW button, like you're supposed to. Well, the NORMAL action would have happened, buuuut - I'm on Linux. The next few hours were fueled by "Nah, it couldn't be Linux mucking the box!".

The symptom was like others had said, no lights, (quick flicker of the PC light on power up), no response, everything's hosed, where'd I put that chicken, G-D! Cables, ports, hubs, USB 2 ports, adapters, with/without the PC host cable in...

Grabbed an old Windows laptop... Well, that was easy,.

So, to the other discussions here, I wanted to add:

• The cheaper the WINDOWS laptop the better
  
• YES it could be Linux (not specifically, but..) ***
  
• YES it could be the hub/switch
  
• YES it could be the cable
  

Hello!
I just receive the MRCC and I can do all I want but trying to save presets the machine crash all times. Exactly it freeze. Then, the time I can save a preset later I can not load it. The Load Box is grey and it freeze when I try to do it. Each time I have reboot and do the configuration.
I updated the machine with the last firmware.
Maybe Im doing something wrong?

Thanks in advance!

Hi
I'm a newb/dimwit, so please bare with...

My MPC One is connected to [MRCC] PC and provides the master clock. (MRCC f/w v1.1.073)

When I plug my NDLR, RD-8 mkii, SQ-1 direct into the MPC One, I can assign Sync to them individually (see image)

When the devices are plugged into the MRCC , the MPC can't see them (even though routing is enabled) - I just get MRCC MIDI 1-12.
Is there any way to allow the MPC to recognize and display the connected devices via the MRCC?
Also, the RD-8 starts and stops fine, but not the SQ-1. The NDLR starts after a stutter but also puts out midi clock (red triangle) even though I changed internal clock to USB1.

Sorry, another question... my VK-8 organ module listens on 3 midi channels (DIN), can I filter channels 2 & 13 and just allow channel 16 to reach it?

Thanks for any guidance
Dom

Attached Files

Thumbnail(s)
   

So the manual says I can send CC 73 to change the key of the NDLR

You can see a snapshot of my Ableton session here - see the track labeled 4 MIDI has a clip that is sending CC on 73. The track is set out to send on NDLR (port 1)  out to NDLR via USB.
 

Also here are my MIDI settings in Ableton, note that I have clock working where Ableton is the master (when I press play in Ableton, the NDLR starts up and is synced to Ableton's clock.).


to I had to enable the "Track" preferences for output "NDLR (Port 1)" in order to see it as a listed midi output port (see below) otherwise it wouldn't show up. 
 

But anyways, no matter what value I set the clip's CC value (in picture 1), I don't see the NDLR LED screen changing to reflect any key changes.

I'm using the NDLR with my MPC force, and everything sounds great when I'm just jamming with the sequencer stopped. But when I try to actually let the Force sync to the NDLR, the clock is totally crazy. What am I missing?

NDLR is sending four parts over USB 1, 2, 3, and 4, each part set to Channel 1 on its respective USB part.  Midi clock out is set to USB 1, as I was thinking that setting it to "all" would duplicate the clock over all 4 channels and may have been causing the problem. 

Force still acts like it's receiving multiple clocks at the same time and goes crazy.

So basically the connection from my synth to MPC One works. The MPC One is my master clock. My old midi interface from ESI also passed on the master clock without any problems. Only now when I try to sync on my Sequential (REV2 but also PRO3) with the internal ARP of Sequentials nothing happens. The ARP of both synths does not start. What can be the reason?

Hi,

I can't seem to find any references, either in the MMRC manual or in Youtube videos, to assigning labels to the outputs of the Remote-7.

Can anyone help please?

When I put an LFO on the pad position, the chord drops out every few takes and doesn't send notes in that bar at all. This is very annoying when the complete pad instrument drops out every now and then unconcrolled, so I can't program any movement on the pad position, that's a pity....
Latest firmware is installed. Has anyone observed the similar and maybe found a solution?

I want to switch which DAW I can use. On the one hand I use the AKAI MPC One and on the other hand my PC. Now I would like to make either the MPC or the PC the main sequencer and main host depending on which setup I have. How do I have to connect the devices to enable me to do this. There is only one HOST USB port. Thank you for your support.

Hi there,

I'm using a Komplete Kontrol S61 into Logic Pro X. I can't seem to get MIDI out of the DAW and to my external synths.

I've got the KK connected to the computer via USB.

The MMRC is in 'PC' mode selection, and holding the PC Input button shows Input 1 lit up green. The PC Output button when hold shows all 4 DIN outputs as selected (which is what I want, as I want to send MIDI to all 4 external synths, but on different channels).

Not only am I getting no MIDI out to the DINs, it's also producing a lot of MIDI 'noise' with data coming from somewhere even when I'm not playing.

Can anyone shed any light on what I'm missing here?

Thanks!