I have started experimenting with the 3.5mm TRS outputs (number 11 and 12) connecting to the Korg NTS-1 with a straight (stereo audio) 3.5mm TRS cable. 

Unfortunately the NTS-1 doesn't receive any MIDI data using that cable. Neither the A or B flavors of the TRS ports work.

Using a TRS to MIDI conversion cable on the NTS-1 side works fine, but in that case I will "loose"  a MIDI port on the MRCC. As I have all MIDI out ports on the MRCC in use already, I would like to use the TRS ports as well.

Does anyone have any suggestion on which cable to use to connect 3.5mm TRS on both sides (MRCC and NTS-1)?

Last night I finished adding the last couple of labels, saved them, then scrolled through the list, but midway through the alphabet (sometimes MAC, sometimes Mixer) all following slots were blank: no user created, no factory ones.  The longer I scrolled clockwise, the longer it would take to return to visible entries, so it seems there were just blank slots there.  Power cycling the unit a few times did not resolve the disappearance of the missing items, which included a bunch I had made the previous day.  However, ones in the first half of the alphabet, both custom and factory, are still there.  OS is 1.1.020.

We are currently including a 10 Meter Ethernet cable with orders of the MRCC Remote 7. We would like to get a feel for whether this is a good default length or is it overkill? After completing the survey, feel free to comment below.

I have a question about the number of mods of one type (e.g. CC) for the whole MRCC. Is it possible that only 6 different modifiers of one type can be created in the entire configuration (not a single IN-OUT routing) ?

If this is true then this is a very small amount (if you consider that it has to support such a number of devices, including USB, which often without a computer you can not change anything and you need to do it on MRCC).

In some cases, I would like to use these 6 CC modifiers for only one device... and is this the end of the possibility of changing CC? I hope I'm wrong...  

I am preparing to do a more complicated configuration for different hardware (quite flexible, as there will be several parallel settings for different synthesizers, which will be independently enabled on midi outputs). I will use a large number of modifiers and wonder if after creating a dozen modifiers it will be possible to remember what the individual modifiers are used for (their names are very short).

Is it possible to add an additional field with a description for connection pairs? Using aliases for devices is extremely useful, but it's telling nothing about reason for modifiers. 
If we have keyboard support, and you can even do it in a configuration file, this option would make it easier to understand later how it works.

It could be enough to create description field for each connection, e.g. for IN1 -> OUT3 pairs, a description of "modulation to LFO" or "aftertouch to cutoff on synth3" or "random arp for bassline" etc.

Hi

Im facing some strange issues with the MRCC when connecting the NDLR.

I have a Sqarp Pyramid sequencing some synths (through usb 1) + running the clock, which syncs my computer (Ableton) + all my synths.
This works great (so far).

As soon as i connect the NDLR to one of the MRCC usb ports the clock jumps all over the place (on all devices) 
Even when the NDLR has not been routed to anything.

If i put a filter on clock on the output port of the usb port NDLR is connected to it resolved the "jumping clock", but then the NDLR isnt getting sync

Been messing around with this for a while now and need some pro tips of how to fix this.
Found a post with disabling the clock out completely through the boot menu on the NDLR, but that did not help anything at all. (disabled 2 first options and the last option set to 1 instead of 1-4) 

Was on the "current" beta, but also updated the ndlr to beta fw trying to figure this out + resetting to factory settings etc.

Can the NDLR be run as "slave" with only using USB? 
Also how can this mess up clock on everything even when the USB port its connected to on MRCC isnt routing out to anything?

I see the NDLR sending CC19 (to nothing) every bar on the MRCC display, but all the pads etc are not even set up using USB, so not sure whats going on
help!

update; it works as is should if i use the internal clock on the NDLR, but as soon as i try to "slave" it makes the clock jump around and i would really like to use the pyramid as clock as its quite central in my setup + this also caused the MRCC to freeze up while clock jumping around :|

Hi

Could we please have the black-key note-on messages control the chord degrees in the same order as on the front panel? This is extremely confusing. ("triad-7th-sus2-alt1-alt2-sus4-6th" instead of "alt1-alt2-triad-7th-6th-sus2-sus4" which makes no sense at all and is difficult to memorize: F#3- G#3- C#4- C#3- D#3- D#4- A#3.... go figure :-(

Thanks!

Just received my MRCC yesterday. So far, so great!
I'm trying to connect my Beatstep (non-Pro) via USB in hopes that it can be synced to other gear as the Beatstep only has MIDI Out.
As stated in the Quick Start Guide, the port lights amber and the MRCC needs to be power cycled as the Beatstep is drawing too much power.
I thought that a USB MIDI hub would solve the problem, as it could power the Beatstep and allow MIDI to pass through, but I've read elsewhere in the forum that presently MIDI hubs will not work.
Can anyone suggest a way to power the Beatstep externally while simultaneously allowing it's MIDI to pass back and forth to the MRCC via USB?
Thanks in advance!

I'd like some kind of case or bag that will hold the NDLR or MRCC when I'm not using them (or when I want to take them somewhere). Any suggestions?

Hi

Because the NDLR doesn't send control midi and I want my performance to be recorded to be edited after the fact (but not the generated notes, the actual commands), I try to command the NDLR over midi. After a LOT of headscratching I finally came to the conclusion that the CC commands have a VERY serious erratic lag. This is especially noticeable when changing degrees and alterations with CC's. With notes all is fine. Is there a setting I have missed or is this a known issue?

Thanks!
Dirk

(external controllers used: mainly Pyramid, Launchpad Mini MK3, but they're not part of the problem, believe me)