I'm thinking to order the NDLR along with the MRCC and some accessories.

Just wondering if I'm best placed to wait until the NDLR exits pre-order or otherwise order everything now i.e. will the MRCC etc be held until the NDLR becomes available so everything can ship together? Shipping destination is Australia.

Thanks in advance!

Any idea when the September 2023 NDLR batch will arrive and shipped ?

From the manual and some experimentation it appears that pads with 4 notes or less in them (including canonical triads) will always use the 1st - 3rd - 5th scale degrees in the selected chord (e.g the 1-3-5 in I). 

In electronic music it is common to use an open voicing even for triads, where the middle note is transposed up by one octave/+12 st.  This doesn’t seem possible in any of the NDLR’s pad spread options. Can this be added please?

Hello, so, I have the NDLR "clock in" set to "ClkIn CV" with a chord from a Roland TR-8S "Trigger Out" to "NDLR's CLK IN".

However, while the TR-8S is set to say, 120 BPM the NDLR plays 10 BPM rather than 120, or whatever the BPM may be the NDLR doesn't change to reflect it and stays within that very slow range.

When I switch the clock to anything but internal the BPM changes to 18.5.

 I cannot figure out why this is. Thanks!

So the manual says I can send CC 73 to change the key of the NDLR

You can see a snapshot of my Ableton session here - see the track labeled 4 MIDI has a clip that is sending CC on 73. The track is set out to send on NDLR (port 1)  out to NDLR via USB.
 

Also here are my MIDI settings in Ableton, note that I have clock working where Ableton is the master (when I press play in Ableton, the NDLR starts up and is synced to Ableton's clock.).


to I had to enable the "Track" preferences for output "NDLR (Port 1)" in order to see it as a listed midi output port (see below) otherwise it wouldn't show up. 
 

But anyways, no matter what value I set the clip's CC value (in picture 1), I don't see the NDLR LED screen changing to reflect any key changes.

I'm using the NDLR with my MPC force, and everything sounds great when I'm just jamming with the sequencer stopped. But when I try to actually let the Force sync to the NDLR, the clock is totally crazy. What am I missing?

NDLR is sending four parts over USB 1, 2, 3, and 4, each part set to Channel 1 on its respective USB part.  Midi clock out is set to USB 1, as I was thinking that setting it to "all" would duplicate the clock over all 4 channels and may have been causing the problem. 

Force still acts like it's receiving multiple clocks at the same time and goes crazy.

When I put an LFO on the pad position, the chord drops out every few takes and doesn't send notes in that bar at all. This is very annoying when the complete pad instrument drops out every now and then unconcrolled, so I can't program any movement on the pad position, that's a pity....
Latest firmware is installed. Has anyone observed the similar and maybe found a solution?

Help. I want to playback midi notes to my external device in Ableton with MRCC. But I can't figure out how to do it. See notes in the diagram. 
Also, the external instrument "Moog silmphatty" is plugged into MRCC and can receive notes in Midi channel 2. 

Please advise! Thanks.!

Hi, Regarding the KB Trans mode, would it be possible to allow the black keys to actually play "wrong" / non-diatonic notes, instead of just doubling up on the nearest "right" note? I'm thinking that the best way to implement this would be for the black keys to play one semitone down from the next white key. This would allow you to play "out" and then back "in" as a great way to jazz up a solo and also to use the black keys for passing notes and slurs. It wouldn't take away from the 'safety' of playing in transpose mode - you'd just need to stick to the white keys for that, but it would open up a whole lot of expressive jazz / blues potential for soloing over a chord or chord progression.

Hello there!
I just got a NDLR weekend before last at the Portland Synth and Pedal Expo. 
I was told to download the newest beta firmware off the forum and I have looked all over for it on this forum and don't seem to be able to find it.
Could someone please tell me where it is?
Thanking you all kindly in advance.
Excited to get into this machine!
All the best,
John