Indeed the windows version doesn't matter, it might be some FW tuning.
I just had the MRCC lock up trying to save to user 1 slot
I also don't see a visual confirmation on User 1 slot being updated. I tried to save 5 times now, every time after a reboot the unit still has it's "Factory" settings (being on "save" box Highlighted white and the press blue shift + black middle button (enter) nothing happens, either press and hold shift first, or press both at the same time.
The manual mentioned "green" for updated "banks slots" but does this also count for "user 1/2/3" ?
Then there is the Apple USB keyboard (wired) that doesn't respond when plugged into the A/B/C/D port?
I go to the edit label box use the white keys to get in the box, no response from keyboard?
Overall I think the ergonomics for the OLED buttons are also far less then ideal, The interface could have easily be dealt with with the big rubber rotary encoder to navigate only by a "scrol and push" interface would have worked much faster, more consistent and simpler. Same for saving a "shift + enter" while also having to highlight the save box? makes no sense, either shift + enter anywehere on the save page, or just scrol to the save box and push the encoder.
I'm a bit of an autist with these things.
The good news is once booted properly and configured properly, everything works like a charm, however have not been successful saving these settings (might be me, or manual)
and the unit locking up and needing to power cycle ruins my whole session. As it's not properly discovered anymore in windows.
Which means, Close Cubase, reboot system, start everything again. Non of my other devices have these "in windows" boot issues in session. Cubase deals with them just fine, as ports being added/deleted IN SESSION, but for some reason it doesn't with the MRCC
I stand corrected, the MRCC boots correctly in session, but loads Factory, The issue seems to be saving
Being in on the TOOLS menu (dot 1)
navigate to preset selector
select User 1
Navigate to SAVE box (so it's highlighted)
press an hold BLUE Shift button
press black plastic enter button (between the 2 white buttons)
NOTHING happens (at least no visual confirmation)
Press Shift + Enter again
box locks up. totally bricked, needs power cycle.
I definitely can't save, All other issues above seem resolved, I've did reset the unit (booting while holding green button) and mapping and booting in or outside session now works as expected, but I can't save SHIFT + ENTER bricks the unit
the rolling encoder makes the amber led under the USB PC port react, but OLED screen is locked and even the green button, does not turn the unit into sleep
What am I doing wrong?
after a search, seems to be same issue? https://conductivelabs.com/forum/showthr...light=save
Did update my unit to latest FW as well before setting it up, So I had no hindsight / reference from older versions
I just had the MRCC lock up trying to save to user 1 slot
I also don't see a visual confirmation on User 1 slot being updated. I tried to save 5 times now, every time after a reboot the unit still has it's "Factory" settings (being on "save" box Highlighted white and the press blue shift + black middle button (enter) nothing happens, either press and hold shift first, or press both at the same time.
The manual mentioned "green" for updated "banks slots" but does this also count for "user 1/2/3" ?
Then there is the Apple USB keyboard (wired) that doesn't respond when plugged into the A/B/C/D port?
I go to the edit label box use the white keys to get in the box, no response from keyboard?
Overall I think the ergonomics for the OLED buttons are also far less then ideal, The interface could have easily be dealt with with the big rubber rotary encoder to navigate only by a "scrol and push" interface would have worked much faster, more consistent and simpler. Same for saving a "shift + enter" while also having to highlight the save box? makes no sense, either shift + enter anywehere on the save page, or just scrol to the save box and push the encoder.
I'm a bit of an autist with these things.
The good news is once booted properly and configured properly, everything works like a charm, however have not been successful saving these settings (might be me, or manual)
and the unit locking up and needing to power cycle ruins my whole session. As it's not properly discovered anymore in windows.
Which means, Close Cubase, reboot system, start everything again. Non of my other devices have these "in windows" boot issues in session. Cubase deals with them just fine, as ports being added/deleted IN SESSION, but for some reason it doesn't with the MRCC
I stand corrected, the MRCC boots correctly in session, but loads Factory, The issue seems to be saving
Being in on the TOOLS menu (dot 1)
navigate to preset selector
select User 1
Navigate to SAVE box (so it's highlighted)
press an hold BLUE Shift button
press black plastic enter button (between the 2 white buttons)
NOTHING happens (at least no visual confirmation)
Press Shift + Enter again
box locks up. totally bricked, needs power cycle.
I definitely can't save, All other issues above seem resolved, I've did reset the unit (booting while holding green button) and mapping and booting in or outside session now works as expected, but I can't save SHIFT + ENTER bricks the unit
the rolling encoder makes the amber led under the USB PC port react, but OLED screen is locked and even the green button, does not turn the unit into sleep
What am I doing wrong?
after a search, seems to be same issue? https://conductivelabs.com/forum/showthr...light=save
Did update my unit to latest FW as well before setting it up, So I had no hindsight / reference from older versions