Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
LFO assigne to Midi Controller?
#6
(01-24-2021, 10:23 AM)House de Kris Wrote:
ananda Wrote:Yes, it is the Studio Electronics ATC-1 with 24db filter cartridge! I still love it and keep it in the mix Wink

Thx for the detailed descritption!! It works like a charm. 

The only thing I  can`t figure out: Is it possible to set a min/max value for the modulation: Let`s say set  minimum CC value to 50 and maximum to 127 thus the filter does not completly close? Thus far when I set MOD AMT it only changes the max value.

Glad to hear it works like a charm for you. I was going to suggest setting the pattern to 'chromatic' to allow a range of 60 (to increase the max possible spread of numbers), but I decided to test my recommendation first. It doesn't work at all on my NDLR. Typically, I test my suggestions before writing them, but in my previous message I didn't. 

I'll itemize my steps in case JesseJ wants to help out:
01- I've done all of this on Mod Matrix 6, MIDI-A ch 9, CC#32 (all choosen at random for an example)
02- set Mod Src to LFO 1, which is a 5s TRI Uni waveform
03- adjust Mod Amt to 100%
04- display says Mod Range 0 to 127
05- my external MIDI monitor confirms this
06- adjusting Mod Amt to 50%, display says Mod Range 0 to 63, and the MIDI monitor agrees
07- change Mod Src to LFO 2, which is 1s Patt20
  Patt20 is:
    1- chromatic
    2- 8 steps long
    3- step values of: 60, 51, 15, 60, 32, 18, 21, and 21
08- Mod Amt is reported as 100%
09- Mod Range 0 to 63 is displayed
10- my MIDI monitor says only 0s are being issued
11-twisting ENC 4  (Mod Amt) clockwise (as if to go greater than 100%) keeps Mod Amt at 100%, BUT Mod Range then changes to 0 to 5, or 0 to 2, or 0 to 3
12- Mod Range randomly bounces around at numbers less than 6 for the maximum for each click twisting clockwise on Mod Amt 
13- on occasion the MIDI monitor reports I sometimes get a CC#32 value of 1 or 2 corresponding to the 60 and 51 numbers in my pattern
14- twisting Mod Amt counterclockwise goes to 0% with a reported Mod Range of 0 to 0

In my experience, using a Pattern as an LFO for the Modulation Matrix to spit out CC data doesn't work at all.

Very disappointing.
Ah bummer, I will try and repro this tomorrow. I think what you described should work, so if not we've got a bug to fix. Thanks again Kris.
Jesse
Reply


Messages In This Thread
LFO assigne to Midi Controller? - by ananda - 01-21-2021, 11:58 AM
RE: LFO assigne to Midi Controller? - by ananda - 01-23-2021, 01:08 PM
RE: LFO assigne to Midi Controller? - by Jesse Johannesen - 01-26-2021, 10:30 PM
RE: LFO assigne to Midi Controller? - by Steve - 01-29-2021, 05:19 PM
RE: LFO assigne to Midi Controller? - by ananda - 01-31-2021, 09:33 AM

Forum Jump:


Users browsing this thread:
2 Guest(s)